Swingline 1757392 Instruction Manual download pdf (Page 5)

Operation

Connect the shredder to main supply. Turn the Power Switch to “On” located on

the back of the machine.

Press the center Auto / Off button. This will switch to Auto mode. The Auto

symbol on this button will now turn blue.

To commence shredding, insert paper to be shredded into the feed area. The

jam-free mechanism will sense the thickness of the paper being shredded.

This sets the shredder into auto mode and initiates the ShredMaster Jam-Free

mechanism. You are now able to shred.

Insert paper to be shredded into the feed area. The Jam-Free mechanism will

sense the thickness of the paper being shredded.

If the paper thickness is within the shredders capacity the motor will start and

your documents will be shredded. Cutters will stop once the shredding process

is complete.

If the paper thickness is greater than the shredders sheet capacity the anti-jam

indicator will turn from green to red and the motor will not run.

If this happens, remove some of the sheets from the paper stack and re-try until

the anti-jam indicator reverts back to green, the shredder will then automatically

start and allow the paper to be shredded.

If the shredder is left in auto mode for more than 2 minutes without being used,

the shredder will automatically switch off in order to save power.

Credit Cards (EX10-06 only)

Switch shredder to auto mode and place credit card into the feed area of the shredder.

It is important to place in the center of the shredder as this is where the auto run

sensors are located.

Rare Occasions of Jamming

In the unlikely event of the shredder jamming, use the reverse function to unblock the

shredder. (see Reverse function section)

Alternating between the reverse function and the forward run will help unblock the

feed area. To trigger the permanent forward run mechanism, press forward button

down for 2 seconds.

Once the jam is clear, press the right hand auto button once to revert back to auto

mode. You can now resume shredding as normal.

Bin Full

When bin is full you must empty bin.

• Pull out the bin to empty.

Empty or compress the shredded paper when it reaches the bottom of the viewing

window or the lower row of paper bag viewing holes. This will avoid paper spilling over

or difﬁculty in removing the bin when it is too full.

If the bin is not relocated correctly, the anti-jam indicator will continue to ﬂash red.

Once relocated correctly the anti-jam indicator will return to green.

Over Heating

If the shredder is used continuously for long periods of time the shredder may

overheat. If this occurs the Anti-Jam panel will ﬂash orange.

When the shredder is ready to be used again the orange illustration will stop ﬂashing

and the anti-jam indicator will ﬂash green once again. To resume shredding press the

auto button.

Shredder Waste Bags

Please refer to illustrations to see how to insert and remove paper bag.

Insert recyclable paper bag (1765022) into the shredder bin and hook in place using

the holes punched in the bag and locating points on the front internal bin face and

rear lip. Once full with paper, unfold the doubled over bag ﬂaps to make the full

bag easy to remove from the bin. Tuck over the rear ﬂap before folding over the front

sealing ﬂap and sealing the bag closed using the adhesive strip. Most local authorities

now accept paper for recycling please contact your local authority for

more information. Swingline shredder bag 1765016 could also be used.

Shredder Control Panel

Safety First

This means you should be careful because long hair can become entangled

in the cutting head. This could hurt you.

This means don’t reach into the feed opening of the cutting head.

This could hurt you.

This means be careful of ties and other loose clothing which could become

entangled in the cutting head. This could hurt you.

This means be careful of hanging jewelry and other loose items which could

become entangled in the cutting head. This could hurt you.

This means keep children away from shredder.

This means do not use aerosol sprays anywhere near the unit.

Reverse Function

Should you wish to reverse the shredding direction while shredding a document,

a reverse button (d) has been ﬁtted for your convenience.

By pressing the reverse button the shredding cutters will change direction

allowing the retrieval of the document being shredded. The anti-jam indicator

will turn to red.

The reverse function will only run while the button is being pressed. When the

reverse button has been released the shredder will revert to stand by mode.

To turn back to auto mode simply press the right hand auto button.

This means do not shred compact disks or DVDs

ReverseForward

Auto

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Swingline 1757392 Instruction Manual Page 5

Comments to this Manuals

Related products and manuals for Paper shredders Swingline 1757392